Special Dot Peen Marking

MECCO Marking and Traceability makes a variety of special dot peen marking equipment, accessories and options to solve your direct part marking needs. The versaltile MC2000 Dot Peen marking line is available with a variety of accessories and options including:

Rotary Chuck Devise for marking round parts
Tag Feed System
High Temperature Marking Application
Mobile Marking Station

MECCO FM200 - Dot Peen Flange Coupler Marker

Heavy Duty Automatic Flange Marker Designed for the
Oil and Gas Industry.

<<Click for Details

MC2000 Tag Feed Marking System:

The computer-controlled tag feed marking system is a totally automated system for marking tags up to 150 mm in length on the standard units. Customized machines can be ordered for extremely large tags.

The tag feeder is equipped with an adjustable loading rack, which can be quickly readjusted for a wide range of tag sizes. Standard machine size is 15 mm to 75 mm for width and 20 mm to 105 mm for length.

Tag feed system of operations will be as follows:

Using the thumbscrews you first adjust the stacker that holds the blank tags, once this is completed the guide rails can be adjusted for the width of the tag. You then adjust the pusher rod for the length of tag you are marking.

The tags can be manually advanced until one has been located under the marking head. Once in place the feeder system automatically locks the tag to be marked into place. This locking device assures precise repeatability. After this you need only to program the MC-2000 for your marking requirements.

At this point, you have the options of marking the tag by manually entering the required part number and “X” “Y” coordinates via the keyboard or through the automatic mode. When using the automatic mode you will have the options to down load from another source or to simply use one of the preprogrammed files that you have created.

After marking, the tag system will discharge the tag into a hopper located at the end of the feeder.

The MC-2000 plate feed system is equipped to mark in both manual and automatic modes. The manual mode gives you the ability to perform any one of the tag system functions through a series of push buttons located on the front of the machine. By simply moving the selector switch to the manual mode you can now move the pusher bar forward to check for clearance in the systems rails or mark a single tag to check mark location and quality of mark.

The MC-2000 tag feeder is also equipped with warning signals in case of a system jam or if the machine runs out of tags. The control box can also be programmed to mark a specified number of tags or mark until the stacker is empty.

All of the same characteristics that are found in the standard MC-2000 control box are included in the tag feed system.

Dot Peen General Specifications

Electrically driven pusher
Adjustable push bar
Two- (2) tag feed bars for different size tags
Four inch high stacker
One (1) tag weight with handle
Sixteen inch tag transfer table
Spring-loaded computer activated tag lock
Four-inch restacker chute
Adjustable slotted base
Manual/Automatic capabilities
Includes all wiring and software to work with the standard MC-2000
One (1) operator’s manual
Spare parts for complete machine include:
1-limit switch for tag unit
1-limit switch for MC-2000 unit
1-solenoid
1-spring
1-pin
1-oil
1-grease
1-set fuses
1-pin guide wrench

Mobile Dot Peen Marking Station:

Portable table

All steel construction
Tabletop is non-slip vinyl-matted 36” long x 22” wide
Bottom shelf 30” long x 20” wide
Wrap around bumper
14” x 20” x 5” small parts drawer with cylinder lock and keys
Six 3-prong grounded outlets on a plug strip with circuit breaker
Full pneumatic wheels, 2 swivel 2 rigid with brakes

Heavy Duty Retractable Electric Reel

Automatically retracts
125 volts
10 amps
7-3/4” wide x 12” deep x 12-3/4” high
Nema 4 rated
Cord length 30 foot

Air Line Reel

Double o-ring seal
Pressure rating to 250 P.S.I.
Ratchet engagement
Fully enclosed and replaceable rewind spring
Adjustable guide arms
1” solid steel axle
Full flow brass swivel joint
Overall size 17-1/4” long x 7” wide x 18-1/4” high
30 foot of 3/8”I.D. hose

Note: Components subject to change.